Licensed plumbers for kitchen and bathroom sinks across Minnehaha County
Sink installation Sioux Falls SD done right the first time
When you need sink installation Sioux Falls SD homeowners can count on, our licensed team handles kitchen and bathroom sinks from start to finish. We cut out the old unit, check the shut-off valves and supply lines, set the new basin level, and pressure-test every connection before we leave. Whether it is a Saturday morning swap or a same-day emergency, we show up with the right tools and get your water running where you want it.
Live dispatcherUpfront optionsBacked workmanship
What's included
What our sink installation includes
Every sink install starts with removal of the old basin and ends with a pressure test. What we include depends on the sink type and the condition of your existing plumbing. Here is what is standard on a typical job, and what we quote separately if we find it.
Old sink removal
We disconnect the faucet, drain, and disposal, then cut through old caulk and putty to lift the old basin out. We scrape the countertop clean and check the cutout for cracks or soft spots. The old sink goes in the truck unless you want to keep it.
New sink setting and sealing
We set your new drop-in, undermount, or farmhouse sink into the opening, check level both ways, and seal with the correct product for your counter material. Undermount sinks get new mounting clips or epoxy anchors rated for the weight.
Drain and trap rebuild
New basket strainer, new tailpiece, and a P-trap set to code slope. We check the trap arm and vent so the sink drains fast and sewer gas stays out. If the old drain was S-trapped, we correct it while the cabinet is open.
Supply line and valve check
We connect new braided supply lines and test your shut-off valves. If a valve will not close or is weeping, we replace it. That is the number one cause of a second leak after a sink install, and we would rather fix it now.
Pressure test and cleanup
We fill the basin, pull the stopper, and watch every joint under full pressure for at least five minutes. Any weep gets fixed before we pack up. Then we wipe down the counter, haul away debris, and show you the shut-off location.
Service overview
What sink installation Sioux Falls SD actually involves
Sink installation is the removal of an existing basin and the fitting of a new one, including the faucet, drain assembly, garbage disposal connection, and watertight seals at every joint. We shut off the water, disconnect the supply lines, cut through old plumber's putty and caulk, then set the new sink into a clean, level cutout. Underneath, we rebuild the P-trap, tighten the basket strainer, and check that the shut-off valves still turn freely. If the cabinet floor is soft from an old leak, we tell you before we cover it up.
In Sioux Falls, most sink replacements happen for three reasons: a cracked porcelain basin, a faucet that has corroded into the sink deck, or a remodel where the old sink no longer fits the new countertop. Homes in older neighborhoods like Pettigrew Heights and Cathedral Historic District often have original cast-iron drains that need adapting to modern PVC pipe. If you have been searching for sink installation in Sioux Falls SD near me, we serve the whole city and can usually schedule a same-day sink installation Sioux Falls visit when you call before noon.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our sink installation process works
The process flexes to the condition, but these checkpoints keep decisions clear.
Phone assessment
You call, we ask what kind of sink, what cabinet, and whether the old one is leaking now. That tells us what parts to load. We give you a clear arrival window, usually two hours, and call when we are on the way. If it is an emergency, like water pouring into a cabinet, we treat it as priority.
Shut off and remove
We shut off the angle stops, drain the lines, and disconnect the faucet, disposal, and drain. Old putty and caulk get scraped clean. If the shut-off valves will not close, we replace them before anything else. Removal takes 20 to 40 minutes on a standard kitchen sink.
Fit and seal
We set the new sink into the cutout, check level in both directions, and seal with plumber's putty or silicone depending on the material. Undermount sinks get new clips or epoxy anchors. We align the faucet and handle orientation so it works with your cabinet doors and your reach.
Connect and test
New supply lines go on, the P-trap is rebuilt to code slope, and the disposal is reconnected if you have one. We fill the basin, pull the stopper, and watch every joint under full pressure for at least five minutes. Any weep gets fixed before we pack up.
Clean up and walkthrough
We wipe down the counter, haul away the old sink if you want, and show you what we did. You get a plain-language rundown of the shut-off location and any maintenance tip. Total time for a standard swap is two to four hours.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Pipe wrench and basin wrench
For loosening supply line nuts and faucet mounting nuts in tight cabinet spaces. A basin wrench reaches where a regular wrench cannot, so we do not force anything and crack the sink.
Pipe cutter
For clean cuts on copper pipe and PEX tubing when we replace shut-off valves or repair a damaged stub-out. A square cut means a better solder joint or crimp connection.
Soldering torch and PEX crimping tool
For copper pipe repairs we sweat a new fitting with solder and flux. For PEX tubing we use a crimping tool and the correct rings. Both methods meet South Dakota plumbing code.
Drain snake and hydro jetter
For clearing the branch line before a new sink goes in. A hand snake handles most kitchen clogs. A hydro jetter scours grease and scale from the pipe walls so the drain stays open longer.
Sewer camera
For checking the main line when a sink backs up repeatedly. The camera shows roots, breaks, or a belly in the pipe. We show you the video before we recommend a repair.
Pressure gauge
For checking household water pressure before we connect a new faucet. High pressure wears out cartridges and supply lines fast. If it is over 80 psi, we recommend a pressure-reducing valve.
Use cases
When to schedule a sink installation
These examples show how the service framework adapts rather than forcing every call through one repair.
Bathroom vanity sink for a rental unit
A landlord in Pettigrew Heights had a cracked porcelain vanity sink with a leaking pop-up drain. Water was dripping into the cabinet and the tenant had stopped using the sink. The unit needed to be rentable within a week. → We installed a new vanity sink with a Delta faucet and pop-up drain, replaced the supply lines, and sealed the countertop. The job took three hours. The cabinet stayed dry through a full pressure test and the tenant moved back in the next day.
Farmhouse sink install in a Stonegate remodel
A homeowner in Stonegate bought a farmhouse sink online for a kitchen remodel but the granite counter cutout did not match. The disposal was wired to a switch that also controlled an outlet, which is a code violation. → We templated and adjusted the cutout, set the farmhouse sink with new mounting clips, and sealed it with silicone. We rewired the disposal to a dedicated switch and installed a new basket strainer and P-trap. The sink passed a 15-minute pressure test.
Problems we solve
Sink problems we solve for Sioux Falls homeowners
Most sink calls start with water where it should not be. Here are the problems we see most often and how we fix them.
Water pooling in the cabinet under the sink
We find the source with a dry paper towel test on every joint, then repair or replace the failed part. If the cabinet floor is soft, we tell you before we cover it up. We pressure-test after the fix so you know it is dry.
Faucet base corroded into the sink deck
We cut the faucet nuts from below with a mini hacksaw or use a basin wrench with the right leverage. If the sink is sound, we save it. If the deck is cracked, we quote a new sink and install it the same visit.
Slow drain that backs up after a new sink goes in
We run a drain snake or hydro jetter through the branch line while the cabinet is open. If the clog is deeper, we use a sewer camera to see the main line. We clear it first, then finish the sink install.
Shut-off valves that will not close
We replace angle stops with new quarter-turn ball valves in copper pipe or PEX tubing. That gives you a shut-off that actually works. We test it before we connect the new supply lines.
Pricing process
What sink installation costs in 2026
$180 - $850 depending on scope
Sink type and mounting
A drop-in sink is the simplest and cheapest to install. Undermount sinks require clips or epoxy anchors and more careful sealing, which adds labor. Farmhouse and apron-front sinks need cutout adjustments and extra support, so they cost more.
Countertop material
Laminate and solid-surface tops are easy to work with. Granite, quartz, and quartzite need diamond blades or existing cutouts, and we take extra care not to chip the edge. If we have to enlarge a cutout, that adds time.
Condition of shut-off valves
If your angle stops close and reopen cleanly, no charge. If they are frozen or weeping, we replace them with new quarter-turn ball valves. That is a small part cost plus labor, and it prevents a flood later.
Customer reviews
What Sioux Falls homeowners say
★★★★★
“Our kitchen sink had been leaking into the cabinet for months before we noticed. The team from Emergency Plumbing Sioux Falls pulled the old cast-iron drain, rebuilt the trap with PVC, and set a new undermount sink in one afternoon. They showed me the corroded shut-off valve they replaced and tested everything twice. No drips since. Worth every penny.”
★★★★★
“I manage four rentals near Pettigrew Heights and needed a bathroom sink swapped fast between tenants. Called at 9 a.m., they were there by 1 p.m. the same day. New vanity sink, new faucet, new supply lines, all done in under three hours. They hauled the old sink away and left the bathroom cleaner than they found it. I have their number saved.”
★★★★★
“We bought a farmhouse sink online and had no idea if it would fit our granite counter. The plumber checked the template, confirmed the cutout, and installed it with new clips and a proper seal. He also caught that our disposal was wired wrong and fixed it. The sink has been solid for months and the cabinet stays dry.”
How much does sink installation cost in Sioux Falls SD?
Most standard sink installations in Sioux Falls run $180 to $450 in labor in 2026, plus the sink and faucet if you have not bought them. A simple drop-in kitchen sink with existing shut-off valves sits at the low end. Undermount sinks, granite cutouts, new valves, or a garbage disposal add to the total. We quote the labor before we start so you know the number.
How long does sink installation take in Sioux Falls South Dakota?
A standard kitchen or bathroom sink swap takes two to four hours. That includes removal, cleanup of old putty, setting the new basin, rebuilding the drain, and testing. If we find corroded shut-off valves, a cracked tailpiece, or a cabinet floor that needs repair, add one to two hours. We do not rush the pressure test, because that is where leaks show up.
Can you install a sink I purchased in Sioux Falls?
Yes. We install customer-supplied sinks all the time, whether you bought it at a Sioux Falls big-box store or ordered it online. We check the cutout dimensions against your countertop before we start. If the sink does not fit or is missing mounting hardware, we tell you right away. Bring the template and any clips or brackets that came in the box.
Do you install kitchen and bathroom sinks in Sioux Falls SD?
We install both. Kitchen sinks, bathroom vanity sinks, laundry tubs, and bar sinks are all standard work for us. We handle drop-in, undermount, farmhouse, and vessel styles. Bathroom sink installation South Dakota jobs often include swapping the faucet and pop-up drain at the same time, which saves you a second service call later. Call with your model and we will confirm fit.
Related services
Related Services
Emergency Plumbing Repair
A sink that leaks into the cabinet is an emergency we handle 24/7. We shut off the water, stop the damage, and repair the line or valve the same visit. If your sink install uncovers a bigger supply problem, we fix it before it floods the kitchen.
Plumbing Installation
New sink installs often pair with other fixture upgrades. We install faucets, disposals, and shut-off valves in the same trip so you are not paying two call-out fees. One licensed plumber, one visit, everything tested together.
Drain Cleaning
If your old sink drained slow, the new one will too until the line is cleared. We run a drain snake or hydro jetter through the branch line while the cabinet is open. That way your new sink starts with a clean pipe and no standing water.Ready when you are
Book your sink installation Sioux Falls SD today
Licensed, insured, and ready to work. We quote the labor before we start, show up in a two-hour window, and test every joint before we leave. Call now and we will get your new sink in and running.
Talk with the local team
Request Sink Installation
Phone is the fastest way to reach us, day or night. A live dispatcher answers 24/7, takes your address and problem, and sends the nearest truck. For routine work we schedule same-day or next-day visits across Sioux Falls and Minnehaha County, including the 57103, 57106 and 57108 ZIP codes.