Licensed plumbers, code-correct rough-in, clean tile-ready finish
Shower installation Sioux Falls SD built to last
If you need shower installation Sioux Falls SD homeowners can count on, we handle the whole job: tear-out, shower pan installation, valve and drain work, and a watertight finish ready for tile or a prefab surround. We serve Minnehaha County from downtown to the west side, and we do same-day shower installation Sioux Falls calls when the old unit fails. One crew, one price, no surprises.
Live dispatcherUpfront optionsBacked workmanship
What's included
What our shower installation includes
Every job is scoped to your bathroom, but here is what is standard on a full replacement. If you only need part of it, we price that separately and tell you upfront.
Old unit removal
We cut out and haul away the old tub or shower, including the pan, walls, and trim. Debris goes with us, not in your alley. Floor protection goes down before demo starts so the rest of the house stays clean.
New shower pan set
The base is leveled, shimmed, and sloped to the drain so water never pools. We set it on a mortar bed where the manufacturer calls for it, which stops the flex that cracks fiberglass over time.
Valve and drain rough-in
New mixing valve, supply lines, and drain assembly installed and pressure-tested. We solder copper or crimp PEX tubing depending on what is already in the wall, and we check the slope against code before closing up.
Waterproofing and wall prep
Cement board or a waterproof wall system goes up, seams taped and sealed, ready for tile or a prefab surround. This is the layer that keeps water out of your framing, and we do not rush it.
Trim and fixture install
Showerhead, handle, and any grab bars or seats get installed and tested. We run hot water for 20 minutes and check every joint before we call the job done.
Cleanup and walkthrough
We sweep, wipe down surfaces, and walk you through the new unit, including how to care for the pan and drain screen. You get our workmanship warranty in writing before we leave.
Service overview
What shower installation Sioux Falls SD really involves
Shower installation is the removal of an existing tub or shower and the rebuild of the waterproof base, drain, mixing valve, and wall system so the unit drains correctly and holds water for decades. We cut out the old pan, check the subfloor for rot, set a new shower pan or tile-ready base, solder or crimp the valve connections, and slope everything to the drain. Nothing gets covered up until it holds water.
Most Sioux Falls calls come from three situations: a fiberglass pan that cracked after a hard freeze, a tub-to-shower conversion for a parent who can no longer step over a 15-inch tub wall, and a 1970s bathroom in Pettigrew Heights or McKennan Park where the original drain is corroded. If you have been searching shower installation near me Sioux Falls and want a walk in shower installation Sioux Falls SD without a three-week remodel, we can usually have you showering again in two to four days.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our shower installation process runs
The process flexes to the condition, but these checkpoints keep decisions clear.
On-site measure
We pull the old trim, check the drain size and location, and look at the subfloor for soft spots. You get a written price the same visit, usually within 45 minutes. If the drain is cast iron and corroded, we flag it now instead of after demo.
Demo and inspection
Day one is tear-out. We cut the old pan or tub into sections, haul it out, and inspect the framing and joists. If we find rot or a slab leak under the pan, we show you photos and price the fix before moving on. Most demo runs three to four hours.
Rough-in plumbing
We set the new drain, slope the pan bed, and run the valve body and supply lines. Copper gets soldered; PEX gets crimped with a PEX crimping tool and pressure-tested. Everything is checked against the Uniform Plumbing Code before the walls close.
Pan and wall set
The new base goes down level and shimmed, then the wall system or cement board goes up. We tape and seal the seams and apply waterproofing so the assembly is ready for tile or a prefab surround. This is the day the job starts looking like a bathroom again.
Trim, test, walkthrough
We install the showerhead, handle, and any grab bars, then run hot water for 20 minutes and check every joint. You get a walkthrough, a care sheet, and our workmanship warranty. Typical total job time is two to four days.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
RIDGID pipe wrench and cutter
Used to break loose old drain fittings and cut out corroded pipe cleanly so the new drain seats without distortion.
PEX crimping tool
Crimps supply line fittings to spec so the connection holds full household pressure without a slow weep behind the wall.
Soldering torch and flux
For copper valve and drain connections where the existing plumbing is copper, giving a permanent, code-compliant joint.
Pressure gauge
We test the new valve and supply lines before closing the wall, so a hidden leak never makes it past rough-in.
Sewer camera
Confirms the drain line is clear and intact before we set a new pan, which matters in older Sioux Falls homes with cast iron.
Hydro jetter
Clears soap scum and scale from a slow shower drain so the new fixture flows the way it should from day one.
Leak detection microphone
Finds hidden leaks behind the wall or under the slab when a stain shows up on the ceiling below the bathroom.
Use cases
When to schedule a shower installation
These examples show how the service framework adapts rather than forcing every call through one repair.
Tub conversion for aging parent
A homeowner near Falls Park needed a safer shower for a parent who could no longer step over the 15-inch tub wall. The bathroom had original galvanized supply lines that choked flow to a trickle. → We converted the alcove to a curbless walk-in, replaced the galvanized run with PEX tubing, and added blocking for two grab bars and a fold-down bench. The job took five days and pressure at the showerhead nearly doubled.
Rental valve leak stopped fast
A landlord in Pettigrew Heights had a tenant report water spraying inside the shower wall. The valve was original to the 1970s build and the wall was starting to show mold at the base. → We isolated the water the same day, replaced the valve and the affected wall section, and set a new pan with a proper slope. The unit was back in service in six days, with the permit and inspection handled by us.
Problems we solve
Shower problems we fix for Sioux Falls homeowners
Most shower calls start with one of these four symptoms. We diagnose the cause before quoting a replacement, because sometimes a repair is the right answer.
Cracked or flexing shower pan
We pull the pan, inspect the subfloor and joists, and replace any soft wood. Then we set a new pan on a proper mortar bed so it does not flex. Most pan replacements are done in a day and a half.
Corroded drain or galvanized supply lines
While the wall is open we replace the drain and run new PEX tubing to the valve. It adds a day to the job and saves you from opening the same wall again in five years.
Tub wall too high to step over
We convert the alcove to a low-curb or curbless walk-in shower and add blocking for grab bars. Most conversions finish in three to five days and keep the same footprint.
Mold or musty smell behind the wall
We open the wall, remove affected material, treat the framing, and rebuild with a waterproof system. Then we find the source, usually a failed pan seal or a leaking valve, and fix it for good.
Pricing process
What shower installation costs
$1,800 - $5,500 depending on scope
Base and wall material
A prefab acrylic surround is the fastest and least expensive option. Tile and cement board add material cost and two to three days of labor because of cure time and setting.
Drain condition and location
If the existing drain is sound and in the right spot, the job is straightforward. A corroded cast iron drain or a relocation for a curbless build adds $300 to $900.
Valve and trim grade
A basic pressure-balancing valve from Moen or Delta costs less than a thermostatic Kohler setup. Trim finish and brand move the number by a few hundred dollars either way.
Customer reviews
What Sioux Falls homeowners say
★★★★★
“Our 1950s tub had a cracked pan and the drain was rusted through. The crew tore it out, replaced the drain and valve, and had a walk-in pan set the next day. They showed me photos of the rot before they fixed it and the price never changed. Three days total and we were showering again.”
★★★★★
“We wanted a curbless shower for my father after his hip surgery. They measured on a Tuesday, installed Thursday and Friday, and added blocking for grab bars like we asked. Water pressure is better than the old unit ever was. Clean work, no mess left behind.”
★★★★★
“I manage four rentals and one had a shower valve spraying inside the wall. They came out same day, shut it down, and had a new valve and pan in by the end of the week. They pulled the permit and handled the inspection, which saved me a trip. I have used them on two other units since.”
How much does shower installation cost in Sioux Falls SD?
Most shower replacements in Sioux Falls run $1,800 to $5,500 in 2026, with a straightforward alcove swap near the low end and a tiled walk-in with new valve and drain near the high end. Prefab surrounds cost less in labor; custom tile adds days and material. If the drain or subfloor needs repair, expect another $300 to $900. We give you the full number before demo starts.
How long does shower installation take in Sioux Falls South Dakota?
A standard prefab shower replacement takes two to three days; a tiled walk-in with a new pan and valve runs four to six. Demo and rough-in eat day one and two, then waterproofing needs time to cure before tile. We schedule the final inspection and walkthrough on the last day, and you can usually use the shower the same evening.
Can you install a walk in shower in my Sioux Falls home?
Yes, and it is one of our most common jobs. We can convert a standard 60-inch tub alcove into a low-curb or curbless walk-in, add blocking for grab bars, and set a bench if the space allows. Older homes near Falls Park sometimes need the drain relocated, which we handle during rough-in. Most conversions finish in three to five days.
Do you handle shower plumbing and tile in Sioux Falls SD?
We handle all the plumbing: drain, pan, valve, supply lines, and waterproofing, and we leave the walls ready for tile or a prefab surround. If you already have a tile setter, we coordinate the handoff. If you want one crew for the wet work and the finish, ask when you call and we will scope it that way.
Related services
Related Services
Emergency Plumbing Repair
If your old shower valve lets go at 2 a.m., we shut the water down and stop the damage before the new install. Same-day emergency response across Sioux Falls.
Plumbing Installation
A shower install often turns into a broader fixture upgrade. We handle valve, drain, and supply work for any bathroom fixture in one visit.
Drain Cleaning
Slow shower drains are usually soap scum and hair, not the pan. We snake or hydro jet the line before install so the new drain flows like it should.Ready when you are
Get your shower installation Sioux Falls SD quote
Licensed, insured, and local since 2017. We measure, price it in writing, and tell you honestly whether you need a full replacement or just a repair. Call now and we will get you on the schedule, often the same day.
Talk with the local team
Request Shower Installation
Phone is the fastest way to reach us, day or night. A live dispatcher answers 24/7, takes your address and problem, and sends the nearest truck. For routine work we schedule same-day or next-day visits across Sioux Falls and Minnehaha County, including the 57103, 57106 and 57108 ZIP codes.