Licensed plumbers for kitchen and bathroom faucet replacement
Faucet installation Sioux Falls SD done right the first time
When you need faucet installation Sioux Falls SD homeowners trust, our licensed team handles everything from a dripping kitchen mixer to a full bathroom faucet replacement. We work on Moen, Delta, and Kohler fixtures daily, and we carry the supply lines, shut-off valves, and plumber's putty to finish the job in one visit. Same-day appointments are available across Minnehaha County.
Live dispatcherUpfront optionsBacked workmanship
What's included
What our faucet installation includes
Every faucet install covers removal, installation, testing, and cleanup. Here is what is standard on the job and what we can add if your setup needs it.
Old fixture removal
We disconnect and remove the existing faucet, including the sprayer and any attached supply lines. The old unit is hauled away. If the fixture is corroded in place, we cut it out carefully to avoid damaging the sink deck.
New supply lines
Standard braided stainless supply lines are included. We size them to reach your shut-off valves without kinking. If your valves are older gate-style, we can swap them for quarter-turn ball valves during the same visit.
Sealing and mounting
We seat the faucet with plumber's putty or a gasket, depending on the deck material, and tighten the basin nut with a basin wrench. This prevents wobble and stops water from seeping under the base.
Pressure and leak test
After restoring water, we run hot and cold for two minutes and check every connection. Any weep is fixed before we leave. We also verify that the sprayer and any dishwasher loop operate correctly.
Cleanup and haul-away
We wipe down the sink and counter, remove packaging, and take the old faucet with us. You get a walkthrough of the new fixture, including how to shut it off and what to check if a drip appears.
Service overview
Faucet installation Sioux Falls SD explained
Faucet installation Sioux Falls SD is a licensed plumbing service that removes your old fixture, preps the sink deck or wall mount, and sets a new faucet with code-correct supply lines and shut-off valves. The job covers shutting off water, disconnecting the old supply lines, cleaning mineral buildup from the mounting surface, applying plumber's putty or a gasket, and torqueing the basin nut so the faucet does not wobble. We pressure-test every connection before we pack up.
Sioux Falls homes deal with hard water that chews through cartridges and seals, so a faucet that drips at 2 a.m. is common in older neighborhoods like McKennan Park and Pettigrew Heights. If you have been searching for faucet installation near me Sioux Falls, we serve ZIP codes 57104, 57105, and 57106 with same-day dispatch. We also handle kitchen faucet replacement Sioux Falls South Dakota jobs where the old fixture has corroded threads or a seized shut-off valve.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our faucet installation process works
The process flexes to the condition, but these checkpoints keep decisions clear.
Phone assessment
We ask what type of faucet you have, whether it is kitchen or bathroom, and whether you already bought the replacement. You get a straight price range on the call, usually $180 to $450 depending on fixture type and access. Same-day slots are held for emergency calls.
Shut-off and removal
The technician shuts off the angle stops under the sink, drains the line, and disconnects the old supply lines. If the shut-off valve is seized, we replace it before proceeding. Removal takes 15 to 25 minutes on a standard kitchen sink.
Deck prep and dry fit
We scrape old putty, clean mineral deposits from the mounting holes, and dry-fit the new faucet. This step catches problems early, like a sink deck that is too thick for the included hardware or a hole pattern that needs an adapter plate.
Install and seal
The faucet goes in with new supply lines, Teflon tape on the threads, and plumber's putty or a gasket at the base. We tighten the basin nut with a basin wrench so the fixture does not shift, then connect the sprayer and any dishwasher loop.
Test and clean up
We restore water, run hot and cold for two minutes, and check every connection with a dry paper towel. Any weep gets fixed on the spot. We wipe down the sink, haul away the old faucet, and walk you through the warranty.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Basin wrench
Reaches the mounting nuts under a sink where a standard wrench will not fit. We use it to tighten the faucet without scratching the finish or stripping the nut.
Pipe wrench
Used on supply-line fittings and shut-off valves. We keep two sizes on the truck for older galvanized and newer brass connections.
Tubing cutter and pipe cutter
Cuts copper pipe and PEX tubing cleanly when we need to shorten a supply line or replace a damaged section during the install.
PEX crimping tool
Makes secure connections on PEX supply lines, which are common in newer Sioux Falls homes. Proper crimps prevent leaks at the fitting.
Pressure gauge
Checks house water pressure before and after the install. High pressure above 80 psi can shorten faucet cartridge life, so we test and recommend a regulator if needed.
Soldering torch and flux
Used for copper pipe repairs when a supply line needs a new fitting. We solder only after the line is drained and the area is protected.
Use cases
When to schedule faucet installation
These examples show how the service framework adapts rather than forcing every call through one repair.
Bathroom faucet upgrade in Pettigrew Heights
Two original widespread faucets leaked at the base and had low flow. The aerators were clogged with scale, and the pop-up drains stuck. The homeowner was tired of water on the counter. → We installed two new centerset faucets with fresh supply lines and cleaned the drain assemblies. Flow returned to normal, the bases sealed tight, and the counters stayed dry. The job took about two hours for both fixtures.
Customer-supplied faucet install in Prairie Green
The homeowner bought a Delta faucet online but the included supply lines were too short for the existing valves. They did not want to risk a leak by installing it themselves. → We supplied longer braided lines, installed the faucet, and connected the pull-down sprayer. The install took 70 minutes, including a pressure test. The homeowner kept the receipt for the fixture warranty.
Problems we solve
Faucet problems we solve for Sioux Falls homeowners
A failing faucet wastes water, stains fixtures, and can damage cabinets. Here are the issues we fix most often on faucet installation Sioux Falls calls.
Dripping faucet that will not stop
We replace the faucet or rebuild the cartridge, depending on age and condition. If the body is corroded, a new fixture is the better long-term fix. We test the new unit at full pressure before leaving.
Low water pressure at one faucet
We clean or replace the aerator, flush the supply lines, and check the shut-off valves. If the restriction is in the pipe, we recommend a pipe repair or repipe and can often handle it during the same visit.
Leak under the sink
We trace the leak to the faucet base, supply line, or drain connection. Most under-sink leaks come from loose packing nuts or failed supply lines, which we replace with new braided lines and Teflon tape.
Frozen or seized shut-off valve
We replace gate valves with quarter-turn ball valves, which close with a quarter turn and resist seizing. This is a common add-on during faucet replacement Sioux Falls South Dakota jobs in older homes.
Pricing process
Faucet installation pricing in Sioux Falls
$180 - $450 depending on fixture type and valve condition
Faucet type
A standard bathroom faucet takes less time than a kitchen pull-down with a sprayer. Wall-mounted and vessel-sink faucets take longer because access is tighter and the mounting hardware is more complex.
Shut-off valve condition
If the valves under the sink are seized or leaking, we replace them during the visit. That adds $75 to $200 depending on access and whether we need to cut into the wall.
Sink deck condition
Corroded or damaged sink decks need cleaning or repair before the new faucet seats properly. Heavy mineral buildup can add 20 to 30 minutes of prep time.
Customer reviews
What Sioux Falls homeowners say
★★★★★
“Our kitchen faucet had been dripping for months and the shut-off valve was stuck. The technician replaced both in about an hour and showed me the old corroded valve. Price matched the quote. No mess left behind. I would call them again for the bathroom faucet.”
★★★★★
“I bought a Delta pull-down faucet online and did not want to mess with the install. They came out the same afternoon, had the right adapters, and had it running in 75 minutes. They also noticed our disposal was loose and tightened it at no extra charge.”
★★★★★
“Both bathroom faucets were original to the 1950s house and leaking at the base. They installed two new widespread faucets and replaced the supply lines. Water pressure is better and no more water on the counter. Clean work and a fair price.”
How much does faucet installation cost in Sioux Falls SD?
Most faucet installs run $180 to $450 in 2026, including labor and standard supply lines. A basic bathroom faucet sits near the low end; a kitchen faucet with a pull-down sprayer and a new garbage disposal connection pushes toward the top. If we have to replace seized shut-off valves or repair a corroded sink deck, add $75 to $200.
How long does faucet installation take in Sioux Falls South Dakota?
A standard kitchen or bathroom faucet takes 60 to 90 minutes from shut-off to cleanup. Wall-mounted or vessel-sink faucets can take two to three hours because of tighter access. If your shut-off valves are frozen or the old fixture is corroded in place, plan on an extra 30 to 45 minutes. We confirm the time window when you book.
Can you install a faucet I purchased in Sioux Falls?
Yes. We install customer-supplied faucets from Moen, Delta, Kohler, and other brands regularly. Keep the box, manual, and any included hardware handy. We check that the fixture matches your sink hole configuration before we start. If a part is missing, we usually have a compatible replacement on the truck.
Do you install kitchen and bathroom faucets in Sioux Falls SD?
We install both. Kitchen faucet installation Sioux Falls SD jobs include pull-down, pull-out, and standard deck-mount models, plus sprayer and dishwasher loop hookups. Bathroom faucet installation Sioux Falls South Dakota work covers centerset, widespread, and single-hole models. We also handle utility sink and laundry faucets.
Related services
Other plumbing services we offer
Emergency Plumbing Repair
A failed faucet supply line can flood a cabinet in minutes. We handle after-hours emergency plumbing repair across Sioux Falls, including burst lines and failed shut-off valves, so you are not mopping at midnight.
Plumbing Installation
If you are remodeling a kitchen or bath, our plumbing installation service covers sink, faucet, disposal, and supply-line rough-in. We coordinate with your countertop timeline so the faucet goes in after the stone is set.
Drain Cleaning
Slow drains often show up right after a faucet swap when debris gets stirred up. We clear kitchen and bath drains with augers and hydro jetters, restoring full flow without harsh chemicals that damage new fixtures.Ready when you are
Book faucet installation Sioux Falls SD today
Licensed, insured, and warrantied. We answer the phone 24/7 and can often be at your door the same day. Call now for a straight price on your kitchen or bathroom faucet install.
Talk with the local team
Request Faucet Installation
Phone is the fastest way to reach us, day or night. A live dispatcher answers 24/7, takes your address and problem, and sends the nearest truck. For routine work we schedule same-day or next-day visits across Sioux Falls and Minnehaha County, including the 57103, 57106 and 57108 ZIP codes.